New 2100 Minimum Till Ripper

Tillage
REQUEST A QUOTE
REQUEST A QUOTE
Key Features
  • Variety of working widths available
  • Mainframe extensions
  • Setback brackets for staggered standard pattern
  • 3/4-in. straight shear-bolt standard minimizes soil and residue disturbance

More Info

Features

Variety of working widths available

The 2100 Minimum-Till Ripper is available in working widths from 2.29 m to 6.86 m
(7 ft, 6 in. to 22 ft, 6 in.).

 

Working width

Number
of standards

Spacing

2.29 m (7 ft, 6 in.)

3

762 mm (30 in.)

2.74 m (9 ft)

3

914 mm (36 in.)

3.05 m (10 ft)

4

762 mm (30 in.)

3.81 m (12 ft, 6 in.)

5

762 mm (30 in.)

4.57 m (15 ft)

5

914 mm (36 in.)

5.33 m (17 ft, 6 in.)

7

762 mm (30 in.)

6.86 m (22 ft, 6 in.)

9

762 mm (30 in.)

6.86 m (22 ft, 6 in.) fold

9

762 mm (30 in.)

 

Stabilizer wheels ensure straight travel and provide support
Adjustable stabilizer wheelsAdjustable stabilizer wheels
#

Two adjustable 521-mm x 203-mm (20.5-in. x 8-in.) stabilizer wheels are included in base equipment to ensure straight travel and provide support on three-, four-, five-, and seven-standard sizes. The nine-standard size has four stabilizer wheels.

 

The stabilizer wheels are designed to stabilize the unit and are not intended to be used as depth gauge wheels. The weight of the unit must be carried on the tractor.

Additional stabilizer wheels and tires can be added if field conditions warrant more support.

Closing wheel available to minimize surface disturbance
Closing wheelClosing wheel
#

Closing wheels can be added to the rear of the 2100 Minimum-Till Ripper with 19-mm (0.75-in.) standards.

Closing wheels offer the following benefits:

  • Minimize surface disturbance created by the standard
  • Provide more adjustments to match farming practices and varying soil conditions than competitive models
  • 114 kg (250 lb) of down pressure
  • Mounted close to the shank, allowing a high trip clearance for operation through washouts, etc.
  • Mounted with an L-bracket, allowing better soil and residue flow
Spring-cushion coulters enable more level soil profile
Straight blade shownStraight blade shown

Cushion coulters cut and size residue and pre-slice the soil to allow a more level soil profile:

  • 559-mm x 5-mm (22-in. x 0.177-in.) straight blade is in base equipment and allows the least amount of soil and residue disturbance.
  • 559-mm x 5-mm (22-in. x 0.177-in.) rippled blade is optional equipment for use when increased soil movement is desired.
Heavy-duty frame handles tough operating conditions
Frame on seven-standard modelFrame on seven-standard model
#

The frame is constructed with a 102-mm x 152-mm x 10-mm (4-in. x 6-in. x 0.375-in.) cross tube on three-, four-, five-, and seven-standard machines and 152-mm x 152-mm x 10-mm (6-in. x 6-in. x 0.375-in.) cross tube on nine-standard models where the hitch-mounting components are welded for maximum strength.

 

Truss tubes connect the cross tubes and are constructed with 127-mm x 127-mm x 13-mm (5-in. x 5-in. x 0.5-in.) steel tubing.

 

Welded together into one assembly, the frame is designed to handle the most severe operating conditions.

 

The mainframe is 4.06-m (160-in.) wide and is the same whether there are five shanks on 762-mm (30-in.) spacings. Frame extensions make this task possible and make configurations easier to adjust.

2100 Drawn Hitch option available for seven- and nine-standard models
Nine-standard drawn hitchNine-standard drawn hitch
#

A drawn hitch option is available for those who want to use large row-crop tractors or 4WD tractors without a 3-point hitch.

The drawn hitch is only compatible with seven-standard and nine-standard 762-mm (30-in.) models. The drawn hitch is also available as an attachment for field conversion.

The transport wheels are placed in front of the front rank of the mainframe. This allows residue to flow freely and keeps the wheels close to the standards to allow the ripper to follow the ground contour.

The wheel modules are mounted to the front, rear, and end frame of the ripper, making it the most stable wheel package in the in-line ripper market. The tires are placed directly in front of the ripper standards so the shanks can remove the tire track in order to leave as level a profile as possible.

There is no need for stabilizer wheels with the drawn hitch. The wheels are located within 762-mm (30 in.) of the outside edge of the machine to provide stability in both field and transport conditions.

The nine-standard model has eight-bolt hubs and spindles with beefy 12.5L-15 tires. The seven-standard model uses 11L-15 tires. The large tires provide excellent field flotation and transport stability.

A pressure-compensating flow divider is the heart of the depth control system. Temporary adjustments can be made while maintaining the ability to raise and lower evenly.

The machine does not need to be fully raised at the end of a pass to keep the cylinders in phase, and cylinder stops are used to set the overall operating depth.

NOTE: The drawn hitch attachment is only compatible with serial number 1300 or newer machines.

Seven-standard drawn hitch foldedSeven-standard drawn hitch folded
19-mm (0.75-in.) straight shear-bolt standard minimizes soil and residue disturbance at the surface
19-mm (0.75-in.) ripper standard19-mm (0.75-in.) ripper standard
#

The 19-mm (0.75-in.) straight shear-bolt standard design moves through the soil minimizing soil and residue disturbance at the soil surface.

  • Equipped with replaceable wear shins to control wear on the leading edge of the shank that greatly extends the life of the standard, unlike some of the competitive models
  • Can only be equipped with 64-mm, 178-mm, or 254-mm (2.5-in., 7-in., or 10-in.) min-till ripper points

The 19-mm (0.75-in.) straight standard is base equipment. It is also available as an attachment for field conversion.

Specifications

Compare >>>

Select up to 2 models to compare specifications

John Deere2100 Minimum Till Ripper
Add Model
Add Model
Tool configuration
Type In-line ripper
Option 1 3-standard, 30-in. spacing
Option 2 3-standard, 36-in. spacing
Option 3 4-standard, 30-in. spacing
Option 4 5-standard, 30-in. spacing
Option 5 5-standard, 36-in. spacing
Option 6 7-standard, 24-in. spacing
Option 7 7-standard, 30-in. spacing
Option 8 7-standard, 36-in. spacing
Option 9 9-standard, 22-in. spacing
Option 10 9-standard, 24-in. spacing
Option 11 9-standard, 30-in. spacing (rigid)
Option 12 9-standard, 30-in. spacing (folding)
Option 13
Option 14
Option 15
Option 16
Option 17
Option 18
Option 19
Option 20
Option 21
Option 22
Working width
Option 1 7, 6 ft, in.
Option 2 9 ft
Option 3 10 ft
Option 4 12, 6 ft, in.
Option 5 15 ft
Option 6 14 ft
Option 7 17, 6 ft, in.
Option 8 21 ft
Option 9 16, 6 ft, in.
Option 10 18 ft
Option 11 22, 6 ft, in.
Option 12 22, 6 ft, in.
Option 13
Option 14
Option 15
Option 16
Option 17
Option 18
Option 19
Option 20
Option 21
Option 22
Transport width
Option 1 10 ft
Option 2 10 ft
Option 3 10 ft
Option 4 13, 6 ft, in.
Option 5 13, 6 ft, in.
Option 6 13, 6 ft, in.
Option 7 13, 6 ft, in.
Option 8 16, 6 ft, in.
Option 9 19, 6 ft, in.
Option 10 17, 8 ft, in.
Option 11 22, 6 ft, in.
Option 12 15, 6 ft, in.
Option 13
Option 14
Option 15
Option 16
Option 17
Option 18
Option 19
Option 20
Option 21
Option 22
Operating depth
Maximum 16 in.
Frame
Size 4x6 x .375 in.
Maximum underframe clearance 36 in.
Operating speed
Miles per hour 4- 5 mph
Horsepower required
Horsepower per standard 30-40 hp
Depth control
Option 1 3-point hitch for intergral
Option 2 single point for pull-type
Option 3
Hydraulic requirements
Option 1 Pull Type - 1 SCV (lift) at 2500 psi for optimum raise times
Option 2 Low transport - 1 SCV (fold) at 2500 psi for optimum raise times
Hitch
Options Intergral or 7-9-standard pull type
Three-point hitch requirements Category 2, Category 3 and 3N (with Quik-Coupler)
Pull-type description Level Lift
Standard options
Spacings 22, 24, 30, 36 in.
Option 1 Trip force
7200 lb. (shear bolt)Standard type
3/4-in. or 1 1/4-in straight with wear shin
Shear-bolt
Option 2 Trip force
3200 lbStandard type
3/4-in. or 1-1/4-in. straight with wear shin
Cushion trip
Option 3
Option 4
Ground-engaging components
Options (3/4-in standard) 7-in. min-till point, 10-in. low-disturbance, 2.5-in. ultra-low-disturbance; (1 1/4-in. standard) 2-1/4-in. regular, 2-1/4-in. capped, 2-1/4-in. double-capped; 2-3/4-in., 5-in., and 7-in. LaserRip points
Coulters
Description
Type Spring cushion coulters
Pounds of force 600 lb. normal working load (4-in. of deflection); 800 lb. maximum trip load (8-in. of deflection)
Blades 22-in. x .177-in. straight or rippled
Closing wheel attachment
Description Two adjustable wheels on 3-, 4-, 5- and 7-standard sizes. Four adjustable wheels on 9-standard integral only. Drawn hitch machines do not require stabilizer wheels.
Down force 250 lb
Size 4 x 16 in.
Spacing 9 to 13 in.
Angle adjustments 0 to 15 degree (angle)
Stabilizer/gauge wheels
Type Stablizer wheels
Wheels 20.5 x 8 in.
Tires 10 PR
Pull-type wheels
Description 12.5L-15 tires for 9-standard pull-type; 11L-15 tires for 7-standard, pull-type; 9-standard has 8-bolt hubs and spindles
Additional feature replacable wear shin
Option 1 set back brackets
Option 2
Option 3
Option 4

Accessories and Attachments

Coulters

Cushion Coulter with .177 In. x 22 In. Blade, Rippled (Qty. 1) - BN909069
Cushion coultersCushion coulters
#

Cushion coulters cut and size residue and pre-slice the soil to allow a more level soil profile.

Cushion coulters are available in two blade choices:

  • 559-mm x 5-mm (22-in. x 0.177-in.) straight blade allows the least amount of soil and residue disturbance
  • 559-mm x 5-mm (22-in. x 0.177-in.) rippled blade for when increased soil movement is desired
Cushion Coulter with .177 In. x 22 In. Blade, Straight (Qty. 1) - BN909068
Cushion coultersCushion coulters
#

Cushion coulters cut and size residue and pre-slice the soil to allow a more level soil profile.

Cushion coulters are available in two blade choices:

  • 559-mm x 5-mm (22-in. x 0.177-in.) straight blade allows the least amount of soil and residue disturbance
  • 559-mm x 5-mm (22-in. x 0.177-in.) rippled blade for when increased soil movement is desired

Frame

Parking Stand (Qty. 1) - BN260494
Parking standParking stand
#

The three- and four-standard machines come with one parking stand in base equipment.

 

The five-, seven-, and nine-standard machines come with two parking stands in base equipment.

 

Extra parking stands can be ordered as a field-installed bundle for increased stability.

Ripper Standard Conversion, Shearbolt to Cushion-Trip

Cushion-Trip Standard Attachment (Qty. 1) - BN260678
Cushion-trip standardCushion-trip standard
  • 1455 kg (3200 lb) of draft trip force and 955 kg (2100 lb) of obstacle trip force to handle the toughest field conditions
  • Shear-bolt protected above 305 mm (12 in.) of vertical-trip height
  • Compatible with existing 19-mm and 32-mm (0.75-in. and 1.25-in.) min-till standards

SETBACK BARS

Setback Bars - BN260673
Setback brackets (1)Setback brackets (1)
Setback bracketsSetback brackets

Setback brackets (1) are available to stagger the standards, allowing increased crop flow in high-residue crop materials.

  • Recommended for use in high corn residue operations
NOTE: The staggered standard pattern is not compatible with the four-standard machine.

Standards

1-1/4 In. Straight Cushion-Trip Standard with Wear Shin (Qty. 1) - BN909924
Cushion-trip standardCushion-trip standard
  • 1455 kg (3200 lb) of draft trip force and 955 kg (2100 lb) of obstacle trip force to handle the toughest field conditions
  • Shear-bolt protected above 305 mm (12 in.) of vertical-trip height
  • Compatible with existing 19-mm and 32-mm (0.75-in. and 1.25-in.) min-till standards
3/4 In. Straight Cushion-Trip Standard with Wear Shin (Qty. 1) - BN909923
Cushion-trip standardCushion-trip standard
  • 1455 kg (3200 lb) of draft trip force and 955 kg (2100 lb) of obstacle trip force to handle the toughest field conditions
  • Shear-bolt protected above 305 mm (12 in.) of vertical-trip height
  • Compatible with existing 19-mm and 32-mm (0.75-in. and 1.25-in.) min-till standards
3/4 In. Straight Shearbolt Standard with Wear Shin (Qty. 1) - BN909921
19-mm (0.75-in.) ripper standards19-mm (0.75-in.) ripper standards
#

The 19-mm (0.75-in.) straight standard design moves through the soil, minimizing soil and residue disturbance at the soil surface.

  • Equipped with replaceable wear shins to control wear on the leading edge of the shank that greatly extends the life of the standard, unlike some of the competitive models
  • Can only be used with min-till ripper points
Closing Wheel Attachment (Qty. 1) - BN260762
Closing wheelsClosing wheels
#
Closing wheels can be added to the rear of the 2100 Minimum-Till Ripper with 19-mm (0.75-in.) standards to minimize surface disturbance.

The wheels are positioned close to the shank to allow increased trip height for going through washouts and depressions.

 

They utilize an L-bracket to attach the wheels, providing better clearance for soil and residue flow.

 

The side-to-side adjustability is 0 mm to 356 mm (0 in. to 14 in.), and the closing wheels attach to the shank with 25-mm (1-in.) diameter hardware.

 

For model year 2007 and older machines, the following parts will be required for one row:

  • One BN260762 closing wheel bundle
  • One N263453 standard casting
  • One N263450 19-mm (0.75-in.) shank
  • Two N263225 spacer shims
Closing Wheel Attachment (Qty. 3) - BN260761

Wheels and Tires

Stabilizer Wheel Assembly with Tire (Qty. 1) - BN909399